DyzEnd-X Hotend 1.75mm
CA$116.00 – CA$140.00
High Temperature and Fast print 3d printer hotend.
Fast Prints
The aluminum melt block transfer heat very quickly to the nozzle for an efficient and very fast printing speed. Furthermore, the long melt zone can handle very high filament feed without any trouble.
Titanium Transition Tube
A titanium alloy has been meticulously chosen to provide both stiffness and low thermal conductivity, limiting heat losses to the cold side.
High Temperature
The high temperature sensor used inside the DyzEnd-X enable precise readings up to 500°C. Any thermoplastics can be used with the DyzEnd-X.
All Metal Melt Zone
The heated zone is made entirely from metals which can withstand very high temperature before losing mechanical properties. Even the sensors and heaters are protected by high temperature resistant sleeves.
Wear resistant nozzle
The DyzEnd-X comes built in with high wear resistant nozzle. The performance have been measured and tested.
Cold Swappable Nozzles
By using a very special high temperature sealing washer, the DyzEnd-X is able to switch nozzles at room temperature. No leaks, no burning hazard.
Flexible Filament Ready
The filament is very well guided inside the DyzEnd-X, which allows very high speed with flexible filament.
Jam Free
The DyzEnd-X perform very well in retraction. The secret is its manufacturing process which enable very low friction inside the tube.
High Resolution Sensor
The unique high temperature sensor has a resolution of 0.16°C at 210°C which is better than a amplified RTD sensor and a thermocouple.
Assembled and Tested
The DyzEnd-X is a high-end product and comes preassembled and tested avoiding the user to have any trouble receiving substandard part that are hard to assemble or fit together.
Connectors
The DyzEnd-X comes with connectors for each electrical component so you can easily maintain it.
Sealing washer
The sealing washer ensure a leak-free operation and makes it easier to switch nozzles.
Liquid Cooling Ready
The DyzEnd-X can be easily converted to a liquid cooled setup with Dyze Design’s specialized cooling blocks.
Bowden Ready
The DyzEnd-X is compatible with a M8x1.25 push to connect fitting. The 4mm PTFE tube can be inserted through the connector and guides the filament as far as possible inside the hotend.
Groove Mount
The hotend mounting mechanism is based on the form factor called “Groove Mount”. The 12mm groove makes it very easy to switch and maintain your hotend and nozzle.
Easy to Mount Sensor
The sensor is installed with elegance using a brass housing. This ensure every hotend read the temperature properly without any variation caused by assembly.
Small Form Factor
By using a low conductivity transition tube, the DyzEnd-X is designed very small. This enables you to use your build volume more efficiently.
Fast heating
The DyzEnd-X can heat very quickly. In only 70 seconds, it reaches 210°C.
Unique Serial Number
The unique serial engraved on each hotend protects the product against clones. Also, it assures a tracking of suppliers, assembly and quality reports.
Any Plastics
The DyzEND-X prints all types of plastics:
- Standard: PLA, ABS
- Flexible: TPE, TPU
- Support: PVA, HIPS
- Advanced: PC, PET, PETE, PETG, NYLON
- Engineering: PEEK, PEI
- Metal powder filled
- Wood filled
- Carbon fiber filled
Download PDF Specsheet Download 3D CAD DyzEnd-X Support
Parameter |
Value |
Units |
Weight – Hotend | 52 | g |
Operating Voltage | 12, 24 | V |
Operating temperature (air cooled) | 0 to +60 | °C |
Operating temperature (liquid cooled) | 0 to +120 | °C |
Top thread | M8x1.25 | mm |
Thermistor resistance at 25°C (500°C) | 4700 | kΩ |
Thermistor resistance at 200°C (500°C) | 8 | kΩ |
Maximum temperature – 40W | 420 | °C |
Maximum temperature – 60W | 500 | °C |
- DyzEnd-X
- Fan with connector
- Heater with Connector
- Temperature Sensor with Connector
- Extension Cables
- 1000mm – Fan
- 1000mm – Heater
- 1000mm – Sensor
- BlackCable Tie
- DyzEnd-X and Dyze Design Stickers
- Additionnal Sealing Washer
Related products
-
DyzeXtruder GT ColdEnd Extruder 1.75mm
Rated 5.00 out of 5CA$205.00High quality and all metal extruder that is able to print any kind of material. High pushing force and dual pinch drive system.
Reviews
There are no reviews yet.