DyzeXtruder GT
Imprime. Plus fort.

La combinaison d'un réducteur, d'un système à double pincement et d'une conception entièrement métallique unique permet au DyzeXtruder GT de pousser jusqu'à 9 kg (20 livres) de force. C'est plus que nécessaire pour toutes les applications d'impression 3D. Pourtant, la DyzeXtruder GT est beaucoup plus légère qu'un extrudeur traditionnel avec un réducteur planétaire, permettant des accélérations plus rapides de l'imprimante.
Only CA$205
Conçu pour une impression avancée
High pushing force
The combination of reduction gear, dual pinch and unique design enables the DyzeXtruder GT to push as much as 9 kg (20 pounds) of force. This is more than necessary for all 3D printing applications.
Conception de dents unique
Motif de dents conçu unique sur le système d’entraînement pour une adhérence maximale, aucun glissement de filament et un débit constant.
Système d’entraînement à double pincement
Le système à double pincement permet une force de poussée plus élevée avec une pression de filament plus faible. Cela réduit le risque d’aplatissement du filament lorsque des impressions très détaillées nécessitent beaucoup de rétractions.
Engrenages protégés
Tous les engrenages sont protégés à l’intérieur du boîtier pour éviter tout dommage causé par la poussière et la saleté.


Moteur inclus assorti
Le moteur inclus est choisi pour correspondre au couple maximal toléré par les filaments. Le moteur ne broiera pas votre filament et empêchera tout dommage à l’intérieur de l’extrudeuse.

petit facteur de forme
Le DyzeXtruder GT n’est pas plus grand que le NEMA 17 qu’il utilise, ce qui le rend très peu encombrant sur une configuration à extrudeuses multiples et l’un des plus petits du marché. L’économie d’espace sur un chariot peut vous permettre d’imprimer de plus grandes pièces sur une seule imprimante.

Lightweight
The gear ratio was chosen to get the best of a very small motor.The DyzeXtruder GT is a lot lighter than a traditional extruder with a planetary gearbox, allowing for faster printer accelerations.
All metal
The aluminum housing is designed to offer a reliable operation, even in a high temperature environment.


Liquid Cooling Ready
The DyzeXtruder GT can be easily converted to a liquid-cooled setup with Dyze Design’s specialized cooling blocks.
Bowden Ready
The DyzeXtruder GT always comes with a special push to connect fitting. A PTFE tube can be inserted through the connector to guide the filament as far as possible inside the mechanism. A single modification in the firmware can easily transform a direct drive setup into a bowden.

Bracketless
The side mounting threads make it very easy to assemble; two M3 screws are included to fit the DyzeXtruder GT on a printer.
Metal Reduction Gears
The DyzeXtruder GT has a 5.65 : 1 gear ratio. This ratio has been chosen to use the full potential of a very small motor while, enabling very high pushing forces. The gears are custom made from high strength hardened steel. This combination allows low friction operations and a longer life. The gears and bearings are designed to last for hundreds of kilograms in extreme conditions.
Easy hotend swapping
The hotend locking mechanism is very practical and rigid.You can secure the hotend in place with only a screw. You can remove it even if there is still a filament inside the extruder due to its turning mechanism. No more hassle of disassembling your setup when you need to maintain your printer.
Easy filament removal and insertion
The unique lockable lever makes filament change very easy and convenient. The locking mechanism holds the lever in position while you change the filament. After, simply push back the lever to disengage the locking mechanism.
Connectors
The DyzeXtruder GT comes with a connector and a cable for its motor so you can easily maintain it.
Caractéristiques de performance typiques
DyzeXtruder-GT Push Force (kg) vs other popular brands
Print any plastics
The DyzeXtruder-GT is able to print every single type of plastic filaments currently sold on the market
Informations technique
| Paramètres | Valeurs |
| Poids | 275g |
| Diamètre du filament | 1.75mm |
| Operating current | 1A |
| Operating temperature (air cooled) | 0°C to +60°C |
| Operating temperature (liquid cooled) | 0°C to +120°C |
| Top fitting tube OD | 4.00mm |
| Gear ratio | 5.65 : 1 |
| Groove mount head thickness | 2 – 5mm |
| Mounting screw thread | M3 |
| Mounting screw min thread depth | 5mm |








